Combination of Surgical Techniques Restores Multidirectional Biomechanical Stability of Acromioclavicular Joint.

PURPOSE: To measure the multiaxial stability of the acromioclavicular joint before and after transection of the acromioclavicular capsule and coracoclavicular ligaments and after sequential repair of acromioclavicular and coracoclavicular ligaments. METHODS: Biomechanical testing was performed on fresh-frozen human cadaveric shoulders (N = 6). Translational and rotational stability in the vertical and horizontal planes was measured in intact specimens, after transecting the acromioclavicular and coracoclavicular ligaments, and after sequentially performing the following procedures: single-bundle coracoclavicular repair (CCR), modified Weaver-Dunn procedure (WD), and acromioclavicular stabilization (ACS). RESULTS: Resecting the acromioclavicular and coracoclavicular significantly reduced translational stiffness in the inferior and anteroposterior directions, as well as rotational stiffness about the vertical and anteroposterior axes. All 3 surgical procedures increased inferior translational stiffness relative to the intact condition (Intact: 38 ± 9 N/mm, CCR: 54 ± 23 N/mm (P = .03), CCR+WD 52 ± 20 N/mm (P = .07), CCR ± WD+ACS 50 ± 21 N/mm (P = .17)). However, the combination of CCR, modified WD, and ACS resulted in the greatest increase in stiffness in internal rotation (Intact: 12.5 ± 7.4 cNm/deg, CCR: 1.2 ± 1.1 cNm/deg, CCR+WD 7.2 ± 3.0 N∗m/deg [P = .023], CCR+WD+ACS 11.6 ± 4.9 cNm/deg [P = .055]). CONCLUSIONS: The cumulative stability of CCR, WD reconstruction, and ACS appears to be additive. Our findings provide a biomechanical justification for combining all three techniques. Biomechanical studies assessing the performance of various acromioclavicular repairs and reconstructions should therefore incorporate multiaxial testing in their protocols. CLINICAL RELEVANCE: Multiple points of fixation that provide multidirectional stability have the potential to improve clinical outcomes and reduce failure rates of acromioclavicular joint repair or stabilization.

Vertical and Rotational Stiffness of Coracoclavicular Ligament Reconstruction: A Biomechanical Study of 3 Different Techniques.

PURPOSE: To compare the biomechanical stability of 3 different coracoclavicular reconstruction techniques under rotational and vertical loading using a cadaveric model. METHODS: In total, 12 cadaveric shoulders were used for testing. The native state was first tested then followed by 3 different reconstruction configurations using suture tapes and cortical buttons: coracoid loop (CL), single-bundle (SB), and double-bundle (DB). Superior displacement was measured by cycling an inferiorly directed force of 70 N to the scapula. The rotational stiffness of the scapula was determined by cycling the scapula in rotational displacement control between 15° of internal and external rotation. The rotational stiffness of the clavicle was determined by rotating the clavicle around its long axis 20° anteriorly and 30° posteriorly in rotational displacement control. All measurements were captured over 10 cycles at a rate of 200 Hz. RESULTS: Both the CL and SB techniques demonstrated significantly less internal scapular rotation stiffness. (intact: 19.70 ± 9.07 cNm/deg, CL: 3.70 ± 2.63 cNm/deg, SB:4.30 ± 2.66 cNm/deg, P <.001) External scapular rotation stiffness was significantly decreased in all techniques (intact: 17.70 ± 4.43 cNm/deg, CL: 3.30 ± 1.37 cNm/deg, SB: 4.50 ± 1.56 cNm/deg, DB: 4.67 ± 1.99 cNm/deg, P < .001). The CL and SB reconstructions were significantly less stiff with regards to posterior rotation of the clavicle (intact: 5.60 ± 1.80 cNm/deg, CL: 2.90 ± 1.10 cNm/deg, SB: 1.40 ± 0.65 cNm/deg, P < .001). Anterior rotation stiffness of the clavicle was significantly lower in all of the reconstructions (intact: 6.95 ± 1.90 cNm/deg, CL: 3.08 ± 0.84 cNm/deg, SB: 3.64 ± 0.93 cNm/deg, DB: 4.48 ± 1.21 cNm/deg, P < .001). CONCLUSIONS: None of the described techniques provided equivalent rotational stability in all planes compared with the native state. DB reconstruction presented stiffness characteristics closest to the native state under cyclic loading during internal scapular and posterior clavicular rotation. CLINICAL RELEVANCE: Additional procedures such as tendon grafting or acromioclavicular ligament reconstruction may be required to control rotational stability.